ChpResults

Provides methods to fetch and read the Chp measurement results.

class nirfmxlte.chp_results.ChpResults(signal_obj)

Bases: object

Provides methods to fetch and read the Chp measurement results.

fetch_spectrum(selector_string, timeout, spectrum)

Fetches the spectrum used for CHP measurements.

Parameters:

• selector_string (string) –

  This parameter specifies a Selector String comprising of the result name.

  Example:

  ”result::r1”

  You can use the build_result_string() method to build the selector string.

• timeout (float) – This parameter specifies the timeout for fetching the specified measurement. This value is expressed in seconds. Set this value to an appropriate time, longer than expected for fetching the measurement. A value of -1 specifies that the method waits until the measurement is complete. The default value is 10.

• spectrum (numpy.float32) – This parameter returns the array of averaged power measured at each frequency bin. This value is expressed in dBm.

Returns:

x0 (float):

This parameter returns the start frequency of the channel. This value is expressed in Hz.

dx (float):

This parameter returns the frequency bin spacing. This value is expressed in Hz.

error_code (int):

Returns the status code of this method. The status code either indicates success or describes a warning condition.

Return type:

Tuple (x0, dx, error_code)

fetch_subblock_measurement(selector_string, timeout)

Returns the power, integration bandwidth and center frequency of the subblock.

Use “subblock<n>” as the selector string to read results from this method.

Parameters:

• selector_string (string) –

  This parameter specifies a Selector String comprising of result name, and subblock number.

  Example:

  ”subblock0”

  ”result::r1/subblock0”

  You can use the build_subblock_string() method to build the selector string.

• timeout (float) – This parameter specifies the timeout for fetching the specified measurement. This value is expressed in seconds. Set this value to an appropriate time, longer than expected for fetching the measurement. A value of -1 specifies that the method waits until the measurement is complete. The default value is 10.

Returns:

subblock_power (float):

This parameter returns the sum of powers of all the frequency bins over the integration bandwidth of the subblock. When you set the ACP_POWER_UNITS attribute to dBm, the parameter returns the total subblock power in dBm of all the active carriers measured over the subblock. When you set the ACP Pwr Units attribute to dBm/Hz, the parameter returns the power spectral density in dBm/Hz based on the power in all the active carriers measured over the subblock.

integration_bandwidth (float):

This parameter returns the integration bandwidth used in calculating the power of the subblock. Integration bandwidth is the span from left edge of the leftmost carrier to the right edge of the rightmost carrier within a subblock. This value is expressed in Hz.

frequency (float):

This parameter returns the absolute center frequency of the subblock. This value is the center of the subblock integration bandwidth. Integration bandwidth is the span from left edge of the integration bandwidth of the leftmost carrier to the right edge of the integration bandwidth of the rightmost carrier within a subblock. This value is expressed in Hz.

error_code (int):

Returns the status code of this method. The status code either indicates success or describes a warning condition.

Return type:

Tuple (subblock_power, integration_bandwidth, frequency, error_code)

fetch_total_aggregated_power(selector_string, timeout)

Fetches the sum of powers in all the subblocks.

Parameters:

• selector_string (string) –

  This parameter specifies a Selector String comprising of the result name.

  Example:

  ”result::r1”

  You can use the build_result_string() method to build the selector string.

• timeout (float) – This parameter specifies the timeout for fetching the specified measurement. This value is expressed in seconds. Set this value to an appropriate time, longer than expected for fetching the measurement. A value of -1 specifies that the method waits until the measurement is complete. The default value is 10.

Returns:

total_aggregated_power (float):

This parameter returns the sum of powers of all the frequency bins over the integration bandwidth of subblock. This value includes the power in the inter-carrier gaps within a subblock, but it does not include the power in the subblock gaps.

When you set the ACP_POWER_UNITS attribute to dBm, the parameter returns the total integrated power in dBm of all the active carriers measured. When you set the ACP Pwr Units attribute to dBm/Hz, the parameter returns the power spectral density in dBm/Hz based on the power in all the active carriers measured.

error_code (int):

Returns the status code of this method. The status code either indicates success or describes a warning condition.

Return type:

Tuple (total_aggregated_power, error_code)

get_subblock_frequency(selector_string)

Gets the absolute center frequency of the subblock. This value is the center of the subblock integration bandwidth. Integration bandwidth is the span from left edge of the leftmost carrier to the right edge of the rightmost carrier within the subblock. This value is expressed in Hz.

Use “subblock<n>” as the selector string to read this result.

Parameters:

selector_string (string) – Pass an empty string.

Returns:

attr_val (float):

Returns the absolute center frequency of the subblock. This value is the center of the subblock integration bandwidth. Integration bandwidth is the span from left edge of the leftmost carrier to the right edge of the rightmost carrier within the subblock. This value is expressed in Hz.

error_code (int):

Returns the status code of this method. The status code either indicates success or describes a warning condition.

Return type:

Tuple (attr_val, error_code)

get_subblock_integration_bandwidth(selector_string)

Gets the integration bandwidth used in calculating the power of the subblock. Integration bandwidth is the span from left edge of the leftmost carrier to the right edge of the rightmost carrier within the subblock. This value is expressed in Hz.

Use “subblock<n>” as the selector string to read this result.

Parameters:

selector_string (string) – Pass an empty string.

Returns:

attr_val (float):

Returns the integration bandwidth used in calculating the power of the subblock. Integration bandwidth is the span from left edge of the leftmost carrier to the right edge of the rightmost carrier within the subblock. This value is expressed in Hz.

error_code (int):

Returns the status code of this method. The status code either indicates success or describes a warning condition.

Return type:

Tuple (attr_val, error_code)

get_subblock_power(selector_string)

Gets the sum of total power of all the frequency bins over the integration bandwidth of the subblock. This value includes the power in inter-carrier gaps within a subblock. This value is expressed in dBm.

Use “subblock<n>” as the selector string to read this result.

Parameters:

selector_string (string) – Pass an empty string.

Returns:

attr_val (float):

Returns the sum of total power of all the frequency bins over the integration bandwidth of the subblock. This value includes the power in inter-carrier gaps within a subblock. This value is expressed in dBm.

error_code (int):

Returns the status code of this method. The status code either indicates success or describes a warning condition.

Return type:

Tuple (attr_val, error_code)

get_total_aggregated_power(selector_string)

Gets the total power of all the subblocks. This value is expressed in dBm. The power in each subblock is the sum of powers of all the frequency bins over the integration bandwidth of the subblocks. This value includes the power in the inter-carrier gaps within a subblock, but it does not include the power within the subblock gaps.

You do not need to use a selector string to read this attribute for the default signal instance. Refer to the Selector String topic for information about the string syntax for named signals.

Parameters:

selector_string (string) – Pass an empty string.

Returns:

attr_val (float):

Returns the total power of all the subblocks. This value is expressed in dBm. The power in each subblock is the sum of powers of all the frequency bins over the integration bandwidth of the subblocks. This value includes the power in the inter-carrier gaps within a subblock, but it does not include the power within the subblock gaps.

error_code (int):

Returns the status code of this method. The status code either indicates success or describes a warning condition.

Return type:

Tuple (attr_val, error_code)